Search Results

This paper discusses the effects of lubricant viscosity on the friction characteristics of engine bearing and cam/tappet which are the typical moving parts of an engine and operate in different lubrication regimes. Based on the measured crankshaft temperatures, we calculated the friction coefficient of the engine bearing according to Sommerfeld number by a simple heat equilibrium equation. The oil film thicknesses between cam and tappet were measured in a motored cylinder head which had a direct acting type overhead camshaft. The boundary and viscous friction components were estimated separately according to a parameter defined as the ratio of the central oil film thickness to the composite surface roughness. These two friction components were added to calculate the friction coefficient. Finally, the motoring friction torque was measured and compared with the estimated friction coefficient.

A preconverter is an essential component of the new vehicle exhaust system for the achievement of tightened emission standards. To meet those standards, the Manifold Catalytic Converter (MCC) system has been developed in the Hyundai Motor Company (HMC). Unfortunately, the conventional MCC is no longer a suitable design for the exhaust gas treatment of the newly developed high performance engine since it cannot withstand the engine's exhaust temperature, vibration, pressure pulsation, and many other severe conditions. This paper is focused on a failure-mode analysis and new packing designs for the MCC application through a series of durability tests.

Today, light connecting rods are vital to satisfying the demands of modern internal combustion engines. HYUNDAI Motor Company (HMC) has applied powder metal forged connecting rods instead of conventional hot forged connecting rods to obtain low product costs and to improve NVH characteristics and bearing reliability. Light connecting rods were developed through optimized design with high quality and low cost. Notably, the mass of a powder metal forged connecting rod is 17.7% lighter than that of a conventional hot forged type connecting rod, and its crank end is 22.5 % lighter than that of a conventional type connecting rod. Light connecting rods result in reduced crankshaft mass, so the mass of the main moving parts can be reduced. With this mass reduction, bearing reliability and NVH characteristics can be enhanced.

To meet Euro6 regulation particulate matter MEMS sensor is suggested. This sensor detects induced charges by PM. To increase sensitivity of the sensor, surface area of the sensor is increased by MEMS process. Sensor is made by low resistive silicon. Total size is 4.3 mm x 59.4 mm x 1 mm and size of sensor part is 4.3 mm x 13 mm. On the backside of the sensor, Pt heater is fabricated to remove piled PM on sensor part. After sensor part, charge amplifier is used to measure the induced charge of the sensor. From FFT of sensor signal, it can sense 5.46 mg/m₃ of PM. In this paper, MEMS devices for exhaust system monitoring of automobiles are investigated. PM emitted from diesel engine is charged particle. Charge-induced-type PM sensor we designed can measure by real time and it doesn't need particle collection apparatus

An experiment has been carried out to investigate the combustion process in an operating S.I. engine (MPI and Multi- valve), using in-cylinder high speed gas sampling techniques. Measurements have been made of local air fuel ratios and time-resolved concentrations of combustion gases such as CO, CO2, THC, NOx, and O2, particularly focused on spark plug location. The effects of fuel injection timing, swirl generating air motion, sampling location, spark timing, speed and load have been considered. With the end of fuel injection at 120° ATDC on the intake stroke, A/F ratio at spark plug location has the leanest value for standard inlet port, while it has the richest value for swirl generating inlet port. The initial NOx concentration in the unburned gas region, diluted by the residual gases, has been substantially reduced between 5° BTDC and 15° ATDC crank angle prior to combustion.

The purpose of this paper is to closely examine the influence of the behavior of fuel mixture in the intake manifold on combustion characteristics, performances of engine output and exhaust emission by using a 4-stroke spark ignition engine. In case of removing the liquid film fuel flowing on the wall of the intake manifold and of not removing it, the values of combustion characteristics such as the heat release delay, the combustion delay, the rate of heat release, the burned mass fraction and the maximum combustion pressure were obtained from the analysis of pressure indicator diagram. And then, the values of engine performance and concentration of exhaust gas were obtained.

As CO2 legislation tightens, the next generation of turbocharged gasoline engines must meet stricter emissions targets combined with increased fuel efficiency standards. Recent studies have shown that the following technologies offer significant improvements to the efficiency of turbocharged GDI engines: Miller Cycle via late intake valve closing (LIVC), low pressure loop cooled EGR (LPL EGR), port water injection (PWI), and cylinder deactivation (CDA). While these efficiency-improving technologies are individually well-understood, in this study we directly compare these technologies to each other on the same engine at a range of operating conditions and over a range of compression ratios (CR). The technologies tested are applied to a boosted and direct injected (DI) gasoline engine and evaluated both individually and combined.

As CO2 legislation tightens, the next generation of turbocharged gasoline engines must meet stricter emissions targets combined with increased fuel efficiency standards. Promising technologies under consideration are: Miller Cycle via late intake valve closing (LIVC), low pressure loop cooled exhaust gas recirculation (LPL EGR), port water injection (PWI), and cylinder deactivation (CDA). While these efficiency improving options are well-understood individually, in this study we directly compare them to each other on the same engine at a range of operating conditions and over a range of compression ratios (CR). For this purpose we undertake a comprehensive simulation of the above technology options using a GT-Power model of the engine with a kinetics based knock combustion sub-model to optimize the fuel efficiency, taking into account the total in-cylinder dilution effects, due to internal and external EGR, on the combustion.

In case of all gasoline vehicles such as the passenger vehicle, heavy duty truck and light duty truck etc., a fuel pump is located inside the fuel tank and transfers the fuel to an engine for stable driving, however, engine stall can be occurred by low pressure fuel pump. The boiling temperature of gasoline fuel is very low, the initial boiling point is around 40°C so fuel can boil easily while driving and end boiling point is around 190°C. It boils sequentially depending on the temperature. It becomes the criteria to determine the amount of vapor released inside the fuel tank at high temperature. The main cause of engine stall at high temperature is rapid fuel boiling by increasing fuel temperature. This causes a lot of vapor. Such vapor flows into the fuel pump which leading to decrease the pump load and the current consumption of the fuel pump continuously. This ultimately results in engine stall.

In this study, the mass of THC is reduced almost 40 percent with spark timing ATDC 7.8CA during 15 seconds from engine start in phase 1 LA4 mode, comparison with TDC 2.8CA (Figure 1, Table 3). One of the reason of HC reduction in vehicle test is reduction of raw THC concentration before CCC (Closed Coupled Catalyst) which is 36% lower level (Figure 3, Table 3). The other reason is that the LOT (Light Off Time) of catalyst is shortened from 34 seconds to below 20 seconds (Figure 7, Table 3). As the spark timing is retarded with same intake air quantity and same RPM, BMEP is reduced (Equation (3), Figure 9). Therefore in order to operate in an idle RPM in vehicle, the mass of intake air should be increased (Figure 5). So a catalyst is heated in shorter period.

The introduction of inexpensive cylinder pressure sensors provides new opportunities for precise engine control. This paper presents a control strategy of spark advance and air-fuel ratio based upon cylinder pressure for spark ignition engines. In order to extend the cylinder pressure based engine control to a wide range of engine speeds, the appropriate choice of control parameters is important as well as essential. For this control scheme, peak pressure and its location for each cylinder during every engine cycle are the major parameters for controlling the air-fuel ratio and spark timing. However, the conventional method requires the measurement of cylinder pressure at every crank angle degree to determine the peak pressure and its location. In this study, the peak pressure and its location were estimated, using a multi-layer feedforward neural network, which needs only five cylinder pressure samples at -40°, -20°, 0°, 20°, and 40° after TDC.

A new concept of misfire detection in spark ignition engines using a wide-range oxygen sensor is introduced. A wide-range oxygen sensor, installed at the confluence point of the exhaust manifold, was adopted to measure the variation in oxygen concentration in case of a misfire. The signals of the wide-range oxygen sensor were characterized over the various engine-operating conditions in order to decide the monitoring parameters for the detection of the misfire and the corresponding faulty cylinder. The effect of the sensor position, the transient response characteristics of the sensor and the cyclic variation in the signal fluctuation were also investigated. Limited response time of a commercially available sensor barely allowed to observe misfire. It was found that a misfiring could be distinguished more clearly from normal combustion through the differentiation of the sensor response signal. The differentiated signal has twin peaks for a single misfiring in a cylinder.

A newly developed surface hardening process, supercarburizing, has been developed for the application of tappet shim to improve fuel economy. Supercarburizing has been introduced to increase resistance of wear and pitting performance and was designed to have supersaturated carbon surface layer and further to have spheroidized carbide morphology. In this presentation, the process variables, such as surface microstructure, morphology and distribution of carbide precipitation, will be discussed via the results of friction loss tests. At an entire speed range investigated, the application of supercarburized tappet shim improved fuel economy with 25∼30% in terms of valve train itself and with 4∼5% concerning on the gross engine performance. The fuel economy analysis showed that the improved surface hardening process of tappet shim increased fuel economy of vehicle about 1.4∼3.6%.

To satisfy the global fuel economy restrictions getting stricter, various advanced cooling concepts, like active flow control strategy, cross-flow and fast warm-up, have been applied to the engine. Recently developed Hyundai’s next generation 4-cylinder 2.0L gasoline engine, also adopts several new cooling subsystems. This paper reviews how 3-D CAE analysis has been extensively used to evaluate cooling performance effectively from concept phase to pre-production phase. In the concept stage, the coolant flow in the water jacket of cylinder head and block was investigated to find out the best one among the proposed concepts and the further improvement of flow was also done by optimizing cylinder head gasket holes. Next, 3-D temperature simulation was conducted to satisfy the development criteria in the prototype stage before making initial test engines.

In recent years, emission regulations have been getting increasingly strict. In the development of engines that comply with these regulations, in-cylinder pressure plays a fundamental role, as it is necessary to analyze combustion characteristics and control combustion-related parameters. The analysis of in-cylinder pressure data enables the modelling of exhaust emissions in which characteristic temperature can be derived from the in-cylinder pressure, and the pressure can be used for other investigations, such as optimizing efficiency and emissions through controlling combustion. Therefore, a piezoelectric pressure sensor to measure in-cylinder pressure is an essential element in the engine research field. However, it is difficult to practice the installation of this pressure sensor on all engines and on-road vehicles owing to cost issues.

Light weighting is a critical objective in the automotive industry to improve fuel efficiency. But when redesigning parts for light weight, by changing from metal to plastic, the resulting design gives NVH issues due to differences in part mass and material stiffness. Many parts were not converted from metal to plastic because of NVH issues that could not be solved. Many engine parts such as cylinder head cover, air intake manifold, oil pan and etc. previously made of metal have since long been replaced with plastic. But timing chain cover has not been replaced because of the aforementioned issue. Sealing performance due to the dynamic characteristics of the application is another challenging factor. In this paper, the key aspects of the plastic timing chain cover as well as its advantage are presented.

The main contribution of this paper is to employ a sound and vibration theory in order to develop a light and cost effective plastic intercooler pipe. The intercooler pipe was composed of two rubber hoses and one aluminum pipe mounted between an ACV (Air Control Valve) and an intercooler outlet. The engineering design concept is to incorporate low-vibration type bellows and an impedance-mismatched center pipe, which replaces the rubber hoses and aluminum pipe respectively. The bellows were designed to adapt powertrain movement for high vibration transmission loss to the intercooler outlet. Also, the impedance-mismatched center pipe was implemented to increase reflected wave by using relatively higher modulus than bellows part and applying a SeCo (Sequential Coextrusion) processing method.

Hyundai Motor Group launched a Continuously Variable Valve Lift (CVVL) engine in 2012. The engine is equipped with HMG's unique CVVL mechanism and is characterized by low fuel consumption, high performance and its responsiveness. The CVVL mechanism is based on a six-linkage mechanism and has advantages of compactness and durability. The engine is a 4 cylinder In-Line, 2.0L gasoline engine and is designed for a mid-sized passenger car. The engine increases fuel efficiency by 7.7% and the peak engine power by 4.2%. One of the most challenging issues in producing a CVVL engine is the valve lift deviations throughout the engine cylinders. The valve cap shim and set screw were designed to adjust the valve lift deviations. Cap shim thickness is chosen by measuring the valve top height, and shoe lift of the cam carrier assembly. The set screw is an auxiliary device to adjust the valve lift deviation.

It is difficult to reach higher compression ratios of the gasoline engine even though higher compression ratios improve thermal efficiency. One of the barriers is large torque drop led by knocking. Extensive researches to suppress knocking of the gasoline engine have been conducted. It is focused on lowering the temperature of fuel mixture in combustion chamber at compression top dead center (TDC). This paper covers the new valvetrain system to decrease the temperature of exhaust valve bottom (combustion) side. Hollow head and stem sodium filled valve (HHSV) have shown more heat transfer from combustion chamber to valve seat insert and valve guide, and higher thermal conductivity valve seat insert (HVSI) and valve guide (HVG) help to decrease valve temperature lower by higher heat transfer.

In diesel engine development, fuel consumption, emissions and combustion noise have been main development objectives for fuel economy, low emissions and NVH. These main objectives can be achieved with advanced engine technologies. As electronic actuating systems are widely applied on diesel engines, elaborate control is required. This is because the main development targets are greatly affected by engine control parameters but frequently have a trade-off relationship. Therefore, the optimization of combustion control parameters is one of the most challenging tasks for improvement. As an efficient method, the DOE methodology has been used in engine calibration. In order to develop a mathematical model, the input and output values must be measured. Unlike other variables, combustion noise has been continually reported to have better indication method in simplified way. In this paper, advanced noise index from cylinder pressure signal is applied on engine test.